Model | 8300 |
---|---|
Years Produced | (2016- current) |
Maximum power at 1800 rpm | 360 kW490 PS/ 483 hp |
Engine | TypePowerTech™ PSS 13.5LExhaust emission regulation compliancy - Final Tier 4 / Stage VDisplacement13.5 L823.8 cu in.ModelEurope: 6135HZ021North America: 6135HZ022CylindersInline 6 |
Fuel system | Unit injector plus four valves |
Fuel tank capacity | 1,100 L290.6 U.S. gal. |
DEF tank capacity ( for FT4 or EU Stage V emission level) | 43 L11.4 U.S. gal. |
Hand wash tank capacity | |
ENGINE POWER | |
Maximum power at 1800 rpm | 360 kW490 PS / 483 hp |
Maximum power at 1900 rpm | |
Rated power at 2100 rpm | 333 kW453 PS / 447 hp |
Fuel tank capacity | 1100 L290.6 U.S. gal. |
DEF tank capacity ( for FT4 or EU Stage V emission level) | 43 L11.4 U.S. gal. |
ENGINE | |
Manufacturer | John Deere |
Type | PowerTech™ PSS 13.5 LExhaust emission regulation compliancy - Final Tier 4 / Stage V |
Model | Europe: 6135HZ021North America: 6135HZ022 |
Displacement | 13.5 L823.8 cu in. |
Cylinders | In line six |
Speed on road | 1400-2100 rpm |
Engine/ground speed management | Optional |
Fuel system | Unit injector plus four valves |
COOLING SYSTEM | |
Cooling system capacity | 113 L29.85 U.S. gal. |
Cooling fan drive | Direct |
DRIVELINE | |
Ground drive | Standard: Hydrostatic, 3-speed - manual shift with helical gearsEngine rpm on road: 1650 rpmOptional: Prodrive™, autoshift transmission, differential lock (automatic and manual), automatic wet brake systemEngine rpm on road: 1400-2100 rpm |
Hydraulics | Load sensing |
Crop harvesting unit | Harvest channel standard |
Crop flow components | Low-friction crop-flow concept |
Main clutch | Dry clutch |
Number of discs | One disc |
Main driveband | Reinforced with Kevlar inserts |
Belt tensioning | Active, hydraulic pressure |
Main driveband, polybelt belts | Six ribs |
HEADER DRIVE | |
Type | Heavy Duty Gearbox (i=3.75)65cc/63cc (pump/motor displacement) |
ELECTRICAL SYSTEM/ELECTRICAL AND HYDRAULIC SYSTEM | |
Type/voltage | 13 V |
Batteries/battery quantity/capacity | 2 x 174 amp-hr |
Alternator | 201 amp |
Hydraulic system capacity | 50 L13.2 U.S. gal. |
GROUND DRIVE | |
Type | Standard: hydrostatic, 3-speed manual shiftOptional: Prodrive™, autoshift transmission |
Differential lock | Manual or automatic (optional comes with ProDrive) |
Maximum transport speed | Hydrostatic transmission: 25 / 30 km/h15.5 / 18.6 mphProDrive transmission: 20 / 25 / 30 / 40 km/h12.4 / 15.5 / 18.6 / 24.9 mph |
Rear axle type | Hydro-mechanical 4WD |
Automatic wet brake system | Available with ProDrive transmission |
Engine rpm - Management | Optional |
MACHINE MANAGEMENT SOLUTIONS | |
Yield monitoring | Harvest Monitor™ optional |
Documentation | Harvest Doc™ optional |
Crop analysis | HarvestLab™ 3000 optional |
Length-of-cut control based on crop parameter | Infinitely variable length-of-cut (IVLOC™) standardAutoLOC™ optional with HarvestLab 3000 |
Satellite (GPS) assisted steering | AutoTrac or Manual RowSense optional |
CROP-HARVESTING UNITS | |
Header height control | Advanced header control (AHC) optional |
Grass pick-ups (transport width) | 3.0, 4.0, 4.5 m9.8, 13.1, 14.8 ftStandard or Premium Line |
Maize or corn headers | |
Driveline | Infinitely variable header driveOptional dual header drive for grass pick-up |
Header connection | Multi-coupler for hydraulic and electricAuto PTO coupler optional |
HARVEST CHANNEL | |
Width | |
LENGTH OF CUT | |
Range | Range at 1100 rpm:40 knives: 7-26 mm (0.275-1.0 in.) LOC / 1 mm (0.04 in.) steps48 knives: 6-22 mm (0.24-0.87 in.) LOC / 1 mm (0.04 in.) steps56 knives: 5-19 mm (0.20-0.75 in.) LOC / 1 mm (0.04 in.) stepsRange at 1200 rpm:56 knives: 4-17 mm (0.16-0.67 in.) LOC / 1 mm (0.04 in.) steps64 knives: 3-15 mm (0.12-0.59 in.) LOC / 1 mm (0.04 in.) steps |
FEEDING SYSTEM/FEEDROLLS | |
Feed roll frame opening | Swing away, 37-45 degree (angle) |
Number | Four |
Metal detector | StandardStone detector is optional |
Width, front | 660 mm26 in. |
Standard feed roll drive | Hydro feedroll drive IVLOC standardInfinitely header drive speed standard |
Optional feed roll drive | |
CUTTERHEAD | |
Type | Dura-Drum™ cutterhead |
Cutterhead housing width | 686 mm27 in. |
Knife drum width | 680 mm26.8 in. |
Knife drum diameter | 670 mm26.3 in. |
Speed at rated engine speed | Standard - 1100 rpmOptional - 1200 rpm |
Knife types available (crop) | Straight - grassCurved - corn |
Number of knives | 40 - 48 - 56 - 64 |
Shear bar, reversible | Grass, corn, or Dura Line Plus |
Shear bar adjust | Fine shearbar adjustQuick shearbar adjust |
KNIFE SHARPENING SYSTEM | |
Reverse rotation | Yes |
Automatic from cab | Yes, remote from cab |
Reverse drive | Standard |
Reverse speed | |
Sharpening modes | Grinding and finishing |
KERNEL PROCESSOR | |
Type | Premium KP (8100-8600)XStream KP (8300-8600) |
Quick-change | Quick kernel processor - swing in/swing out |
Quick KP removal | Optional: Crane with remote-controlled electric hoist |
JOHN DEERE PREMIUM KP | |
Housing | Standard KP housing |
Lubrication | Grease |
Roll diameter | 240 mm9.45 in. |
Speed differential / Roll speed (lower) | 32 percentOptional 40 percent |
Maize, roll teeth number (speed differential) | 118 (32 / 40 percent) |
Wholecrop, roll teeth number (speed differential) | 178 (32 / 40 percent) |
Sorghum, roll teeth number (speed differential) | 238 (32 percent) |
Weight | 320 kg145 lb |
Available KP rolls | Standard sawtoothDuraline sawtoothWhole crop |
JOHN DEERE XSTREAM KP | |
Housing | Heavy duty housing with KP roll quick exchange system |
Roll diameter | Pressurized oil |
Speed differential / Roll speed (lower) | 250 mm9.84 in. |
Bearing temperature monitoring system | 50 percent |
Maize, roll teeth number (speed differential) | Optional |
Wholecrop, roll teeth number (speed differential) | 110 / 145 (50 percent) |
Sorghum, roll teeth number (speed differential) | 145 / 165 (50 percent) |
Weight | 238 (32 percent) |
Available KP rolls | |
Lubrication | Duraline sawtoothDuraline XCutWhole crop XCut |
SERRATED ROLLER (KERNEL PROCESSOR) | |
Maize, roll teeth number (speed differential) | |
Wholecrop, roll teeth number (speed differential) | |
Sorghum, roll teeth number (speed differential) | |
Weight | |
DISK TYPE (KERNEL PROCESSOR) | |
Number of disks (top/bottom) | |
Diameter of disks | |
Weight | |
BLOWER/CROP ACCELERATOR | |
Rotor diameter/housing width | Rotor diameter: 560 mm22.86 in.Housing width: 540 mm21.26 in. |
Number of blades | 10 |
Speed (option) | 1800 rpm |
SPOUT | |
Rotation, degrees | 210 degree (angle) |
Hydraulic height position | Hydraulic raise and lower standardAutomatic spout positioning optional |
Double-cap deflection | Standard |
Number of wear liners | |
Reach from center line (Optional) | |
MAINTENANCE | |
Rotary radiator screen cleaner | Standard |
Automatic lubrication system | AutoLube optional |
Engine oil and filter change duration | JD+50™ II oil: 500 hoursOther oil: 250 hours |
PROPELLING DRIVE | |
Standard | Hydrostatic, 3-speed - manual shift with helical gears |
TRANSMISSION | |
Type | Standard: Hydrostatic, 3-speed - manual shift with helical gearsHydro-mechanical rear axle optional |
Weight and Dimension | |
With front tires | 710/70R42 |
With rear tires | 620/60R30 |
Transport length (without header) | 6.5 m21.4 ft |
Transport width (without header) | 3-3.5 m9.84-11.5 ft |
Transport height (to cab roof) | 3.89 m12.75 ft |
Working height (maximum) | Height to spout: 6.60 m21.65 ft |
Approximate weight (without header) |